The most important part of a car is the engine. The engine can also be said to be the heart of the car. The heart has a problem and the car has to be overhauled, but no matter how it is repaired, it will not return to its original state. Protecting the car's engine can extend the life of the car. In order to ensure that petrol contains a small amount of impurities, some owners will add clear gas to gasoline. This will reduce gasoline deposits and prevent the formation of a thick layer of carbon on the surface of the engine. This kind of cleaning can also soften the carbon layer, so as to achieve the effect of removing the carbon layer. Carbon deposition is the deposition of incomplete combustion of helium in fuel and lubricating oils. The formation of deposits is directly related to the "fuel" and "lubricant" of the car: First, because of the carbon particles contained in the "lubricant" helium gas, a greater amount of deposition occurs in incomplete combustion. The automobile itself contains gums, impurities, or dust and impurities brought in during storage and transportation. It accumulates sludge-like deposits in car fuel tanks, oil inlet pipes, etc. over time; secondly, it is caused by unstable components such as olefins in gasoline. Oxidation and polymerization occur at a certain temperature, forming gums and resinous viscous substances. These sticky substances deposit in the nozzle, intake valve, combustion chamber and other parts will become a hard carbon deposit. In addition, due to urban traffic congestion, cars are often at low speeds and idling, which will further aggravate the formation and accumulation of these sediments. The impact of carbon deposition on the car: 1. Decrease engine power; 2. Increase fuel consumption; 3. Cold start-up difficulties; 4. Severe carbon deposits in combustion chambers also knock off! Acceleration noises at low speeds, on pistons and crankshafts Cause damage; 5. Excess emissions. First, add high-quality gasoline The quality of gasoline in China is far from keeping up with international standards. The price of petrol is a bit better, and the price of gasoline will be deteriorating. Therefore, when we are refueling, we must choose several domestic brands of gas stations, do not choose those miscellaneous brand gas stations, no-name gas station petrol is very difficult to use. When the situation is not allowed, oil with poor quality can be added, and detergent can be added to the gasoline to prevent carbon in the engine. Adding detergents must also be used with care. If you add a counterfeit product, the effect will be even worse. Second, do not drive for a long time The idle time is long, and the time for the engine to reach normal temperature also becomes longer. After the gasoline is sprayed on the back of the valve, the evaporation speed is slow, and carbon deposition occurs. At the same time, often idling, the air flow into the engine is also small, so that the erosion of carbon deposition is also very weak, it will promote the deposition of carbon deposits. Third, run more high-speed, try to increase the manual gear shift speed The purpose of multi-run high speed is to use the effect of airflow on the scouring of the intake port to prevent carbon deposition. In addition, increasing the speed of shifting is similar to that of multi-speed high speeds, converting the original shift to a 2500 shift at a speed of 2,000, which not only can effectively prevent carbon deposition, but also improve the dynamic performance of the car, and also avoids the need for change. Blocking vibration caused by too low speed protects the engine. Fourth, pay attention to the engine break time When the car is equipped with a turbocharger, do not rush to rest in high-speed or uphill conditions, and you should idling for about 10 minutes before stopping. The turbocharged car engine produces carbon layers that are many times higher than those that are not installed. The above method estimates that many drivers will be too inconvenient and have to do maintenance troubles. If you really do not want to do this method, Xiao Bian suggested that the owner of the car in the maintenance of the car every 2 to 40,000 kilometers of the car's steam inlet system again, do not dismantle. Aluminum Profiles are more and more used in the production of doors and windows being their advantages such as light weight, high strength, corrosion resistance, and high cost performance. In addition, aluminum windows and doors have various styles and easy to install. It is an excellent choice for doors and windows of modern buildings. Aluminum Extrusion Manufacturers In Usa,Aluminum Extrusion Usa,Aluminium Extrusion Usa,2080 Aluminum Foshan Knilex Aluminum Co., Ltd. , https://www.aluprofilefactory.com
The best way to solve carbon deposits: